Part Number Hot Search : 
8032B M9306M MBR40 A4956 10T10ACW LEADFREE CH040103 74LVC1G1
Product Description
Full Text Search
 

To Download HFD3381-102 Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
 Fiber Optic LAN Components Connectorized PIN Plus Preamplifier
FEATURES * Prealigned SC Connector sleeve * Data rates from 622 Mbps to 2.5 Gbps * PIN detector and preamplifier in a TO-46 heremtic package * 3.3V operation * GaAs PIN detector and BiCMOS preamplifier * Differential Output for low noise * 2.4 GHz typical Bandwidth
HFD3381-102
The HFD3381-102 is a high-performance 850nm GaAs detector and preamplifier packaged for high-speed data communications. The product is designed for ease of use by the module designer or manufacturer for data rates from 622 Mbps to 2.5 Gbps. The HFD3381-102 converts optical power into an electrical signal that is used in fiber optic communications and other applications. As the light increases, the output voltage increases, limiting at input powers above -10dBm. The differential output is designed to be AC coupled into a data amplifier. The pre-aligned and lensed package with an industry standard SC style connector sleeve, allows for "drop in" assembly to reduce manufacturing cost. The Honeywell HFD3381-102 is designed to interface with 50/125 and 62.5/125mm multimode fiber.
Honeywell
Fiber Optic LAN Components Connectorized PIN Plus Preamplifier
ABSOLUTE MAXIMUM RATINGS
Parameter Storage Temperature Case Operating Temperature Lead Solder Temperature Power Supply Voltage Incident Optical Power Rating -40 to +85C 0 to +70C 260C, 10 sec. 3.8 V 0 dBm average, +4 dBm peak
HFD3381-102
NOTICE
Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operations section for extended periods of time may affect reliability.
ELECTRO-OPTICAL CHARACTERISTICS (Vcc=3.3V, AC coupled to 50, 0CParameters Supply Voltage Supply Current Output Voltage Responsivity Upper 3dB Bandwidth RMS Output Referred Noise Sensitivity Power Supply Rejection Ratio Pulse Width Distortion Rise/Fall Time Wavelength Responsivity Symbol Min. Electrical Characteristics Vcc 3.0 Pin = 0W, Rload=50 Icc Pin = 0W, Rload=50 Vout Pin = 100W, Rload=50 Opto-Electronic Characteristics R Pin = 20W peak, Rload=50 BWupper 2000 Pin=0W, Rload=50 1875 MHz BT Filter BER=10-12, SNR=7 S -17 PSRR 10 Pin=0W, Rload=50 Pin=20W peak, Rload=50 Pin=20W peak, Rload=50 Pin=20W peak, Rload=50 PWD TR/TF 7. 8. Test Condition Typ. 3.3 26 200 1600 2400 500 -20 30 40 250 860 2800 Max. 3.8 50 500 Units Volts mA mV V/W MHz nW dBm dB ps ps nm Notes 1 1 1 2,3 4 5
6 7 8
760
850
Notes:
1. 2. 3. Pin refers to the total optical power at the face of the fiber optic cable input to the HFD3381-102. Responsivity measured with source wavelength of 850nm, 125MHz square wave, Pin=20W peak, Rload=50. The output voltage increases as received light power increases, up to approximately -15dBm. The preamplifier is designed to limit the electrical output signal above this optical input level, and does not introduce signal distortion until the average input power exceeds 0dBm. Bandwidth is measured with a small signal sinusoidal light source with 50 W average power, Rload=50. RMS input referred optical noise is obtained by measuring the RMS output referred noise, then dividing by the responsivity. PSRR is measured from 300KHz to 1GHz by injecting a - 20dB electrical signal on the Vcc pin. The nominal value at 100MHz is recorded. No external bypass components are assumed. An external Vcc filter network will greatly increase the PSRR. Measured at the 50% level of output pulses using 0.5 GHz square wave with <200 ps rise time. Rise and fall times are measured with source wavelength of 850nm, 125MHz square wave, with optical rise and fall times < 200ps, Pin=20W peak, Rload=50.
4. 5.
NOTICE
The inherent design of this component causes it to be sensitive to electrostatic discharge (ESD). To prevent ESDinduced damage and/or degradation to equipment, take normal ESD precautions when handling this product
6.
2 Honeywell *
For application help: call 1-800-537-6945
Fiber Optic LAN Components Connectorized PIN Plus Preamplifier
FIGURE 1: INTERNAL SCHEMATIC DIAGRAM OF THE HFD3381-102 Vcc
HFD3381-102
Inverted Output
Non-Inverted Preamplifier PIN Internal Limiting Amplifier
Ground
FIGURE 2: RECOMMENDED INTERFACE CIRCUIT FOR THE HFD3381-102
HFD3381 R Vcc C1 Ground Inverted Output 50 ohm transmission line Non-Inverted Output 50 ohm transmission line C2 C2
Limiting Amplifier or Test Equipment
Input Input
R=10= C1 = 10 nF C2 = Data rate dependant (22nF for rates > 1Gbps
For application help: call 1-800-537-6945
Honeywell * 3
Fiber Optic LAN Components Connectorized PIN Plus Preamplifier
ORDER GUIDE
Catalog Listing HFD3381-102 Description Connectorized PIN Plus Preamplifier
HFD3381-102
SALES AND SERVICE Honeywell Sensing and Control serves its customers through a worldwide network of sales offices and distributors. For application assistance, current specifications, pricing or name of the nearest Authorized Distributor, contact a nearby sales office or call: TELEPHONE 1-800-367-6786 (USA) 1-800-737-3360 (Canada) +49 (0) 89 35813310 (Germany) +65-580-3312 (Singapore) +44 (0) 118 981 9511 (UK)
MOUNTING DIMENSIONS (for reference only) in./(mm)
PINOUT
Number 1* 2 3 4 Function VCC Inverted Output Ground Non Inverted Output
FAX 1-972-470-4326 (Customer Response Center) 1-972-470-4549 (Fax on demand) +49 (0) 89 3599971 (Germany) +65 445 3033 (Singapore) +44 (0) 118 981 7513 (UK) INTERNET http://www.honeywell.com/sensing/VCSEL INFO.SC@HONEYWELL.COM
Aligned with the Receptacle notch VCC is cut shorter WARRANTY/REMEDY
Honeywell warrants goods of its manufacture as being free of defective materials and faulty workmanship. Commencing with the date of shipment, Honeywell's warranty runs for 18 months. If warranted goods are returned to Honeywell during that period of coverage, Honeywell will repair or replace without charge those items it finds defective. The foregoing is Buyer's sole remedy and is in lieu of all other warranties, expressed or implied, including those of merchantability and fitness for a particular purpose. While we provide application assistance, personally and through our literature, it is up to the customer to determine the suitability of the product in the application. Specifications may change at any time without notice. The information we supply is believed to be accurate and reliable as of this printing. However, we assume no responsibility for its use.
9/1/01
Honeywell Inc. 11 West Spring Street Freeport, Illinois 61032
Printed with Soy Ink on 50% Recycled Paper
006697-1-EN IL50 GLO 797 Printed in USA
Honeywell Inc. Optoelectronics Facility 830 East Arapaho Road Richardson, Texas 75081
Honeywell Control Systems Ltd. Zodiac House Calleva Park Aldermaston, Berkshire RG7 8HW England
Helping You Control Your World


▲Up To Search▲   

 
Price & Availability of HFD3381-102

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X